MartyP
-
Posts
47 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by MartyP
-
-
Heli makes a nice set
-
Hi All,
I want to sell my sargent seat rider and passenger. These are made from the OEM pans so they fit perfect. The seat does not work for me but it may for you. Looking to let them go a fairly good price, DM me if you are interested.
-
OK I ran this again. What I see is that when I put the bike in first gear and let go of the clutch the bike stays at 7 mph. I spray my chain lube on and move on. No error code and I do not touch the throttle. I hope this helps.
-
Had it installed this weekend and I love it. So much more relaxed ride and way easier to work the key. Highly recommend and they look great.
-
On 2/29/2020 at 11:12 AM, littlebruv said:
Are you running the bike in gear on the main stand whilst revving it or idle speed whilst lubing the chain
Idle and 1st gear and a little revving.
-
-
I paid that price in August 2018 for my 2019 GT. I think you can get it cheaper.
- 1
-
I have run my 2019 GT many times on the center stand to lube my chain. Never got a fault code but you know the next time I do it it will go on.
-
Just ordered mine ✌️
-
On 1/21/2020 at 2:01 PM, littlebruv said:
I have just fitted the Yamaha MT09 adventure foot pegs, finally joy at last over the OEM alloy pegs which I think were more like from the R6. Wider and with the main rubber grip insert you notice the difference, only thing I noticed now was the rear brake pedal felt a little lower but that will easily be remedied
With the puig trail pegs I have to raise both the clutch shifter and rear brake.
-
On 1/8/2020 at 9:58 AM, littlebruv said:
Has anyone seen or fitted these Puigs foot pegs yet ?
I just had these installed this weekend. They look nice but the buzz at high rpm's is present. I will say that stock I felt the buzz around 5K rpms with these its about at 8K.
-
-
Hi All,
I can't find this on the manual but I just got new foot pegs installed ( Puig Trail ) and I need to adjust my clutch and rear brake shift positions. I think I can figure out the clutch but the rear brake is a bit odd to me. Any help would be great. I need to raise the shifter and lower the rear brake. Thanks
-
Rox Risers don't fit the GT
-
18 hours ago, skipperT said:
Low. The FJ starts best around when it has 12.7-12.9v to play with.
here’s another test: turn on your key and let the bike sit powered-on for about 30 seconds. Measure your battery voltage with key still on. Less than 12.1-12.2? Dipping well below 12v? 11.8 or less? Your battery is toast.
-SkipMy battery stays at 12.5 even when my charger is on. I did the test and when I started the bike the volts went to 14.1-14.2.
-
I meant the battery pack that I plug my tender into it only lasts a day. Looking at a battery generator but they are $$. I do have a volt meter and my alarm has one as well. currently it show 12.5
-
I live in an apartment and have no outlets to plug the bike in. I have to use a battery pack and only lasts a day.
-
What's the ideal RPM's and gear for optimal charging of the battery. I do a short commute to work 6 miles 30 minutes and I am having issues with my battery holding charge. My scorpio reads 12.5 most of the time and occasionally it will got to 14.1 if I do a longer ride. Thanks
-
I went with the denali D2 trioptic led. Now should I do one spot and one flood? I am looking for more visibility and more attention from the cage drivers.I am mounting them on my crash bars.
-
Hi All,
'Has anyone installed lights on their sw-motech crash bars? If not can anyone recommend a set to me? Thanks
-
On 1/8/2020 at 1:46 AM, dazzler24 said:
@MartyP - This thread might be a start or guide for what you seek.
If you're looking for a direct replacement then it's a +1 for Betony's post above but there are alternatives.
FWIW I replaced mine with the Yausa OEM original - Pricey, but each to their own.
Can you just drop the Yausa in or do you have to flip it around to match the terminals?
-
On 1/8/2020 at 9:58 AM, littlebruv said:
Has anyone seen or fitted these Puigs foot pegs yet ?
I have them but I have not installed them yet. They look very good and good quality as well. I did have to order two yamaha parts for them, both under $2 each.
-
Hi, does anyone know if the CRG Rc2 clutch lever for the MT-09 will fit the Tracer 900 GT?
-
Has anyone replaced the OEM battery? If so which one? Thanks
Rox Risers Question
in Tracer 900 GT Discussions
Posted
My dealer could not get the rox risers to fit.