ilanr1

Even with 1 cable there is enough tension...

Yes , it was the thermostat !!! , it stayed closed. Thanks , all is good now !!! , going for a test ride ...

Hi , i did fill the reservoir bottle to the max level - as it was bellow the minimum level and i added water to the radiator untill the max. No air pockets as i can recognize ... I did some slow ride in the city. When it reach 106C as usual in low city speed i pull over and noticed that a water from the reservoir bottle are going out through the black excess tube . Yes i understand that 106C are above the boiling point of the water and in the reservoir buttle there is no room for the extra water so , in the end i'm still missing water. * i have replaced the radiator cup but it looks like nothing has changed... * No water in the oil. The oil looks ok to me in color . It seems that the ventilator is working hard to reduce the heat , but the heat rise up very quickly after a cooling cycle from the vent. Again we are on winter time now.. i don't want to think what will be in the summer... Any other ideas ?. Thanks

What i found is that the water tank is a lot below the low level and little water is missing in the radiator. What was strange to me is that during a cruising speed on the HWY i have noticed that the temp is like 105-106 celciuse and that is very hot !!!. I usually have a reading in situation like that with a temp like 75 degrees steady reading.

Hi , it looks like the bike is overheating... I will follow the tread that you added and update. Thanks

If my engine temperature is higher what should i check ?. As i mentioned , the water level are right now in the radiator and in the water tank on the side of the bike. No missing of water. So should it be a termostat ? Or a blocked radiator ?. Thanks

Hi , i have noticed that my motor is running a little warm , in the city 85-95 degrees celcius and we are in the winter now... I checked the water level on the radiator and a little water was missing there and also on the water tank. Please share your engine temp in the city and in the highway during summer and winter. What else do i need to check in order to feel good with that issue ?. Thanks

We are dealing here with throttle bodies that have throttle position sentor , accelerator sensor etc.

I saw that there are 2 throttle cables that exists on various models. On my tracer 900 GT 2019 model year , the first is to pull in order to accelerate and the second is to break the cruise control operation - there is a small micro switch that is doing this operation when you push the throttle. So only one cable is enough in a non cruise control models. Second think about a less friction on the throtle movement ... Any thoughts please. Thanks

Update : I took the faulty throttle bodies that i inserted a finger inside them while cleaning to my friend's bike - Tracer 900 2015. I connected the throttle bodies to my friend's bike and follow the diagnostic options , checked that the throttle position switch is under the range , also the accelerator switch it's values are in the range. After that i put it again in my bike Tracer 900 GT and problem solved !!!. It looks that when you insert a finger in the throttle bodies you change the setting of the step motor and you will get a high rpm motor , all you need is just reset it to it's values , i mean Yamaha tool or just Tracer 900 2015...

Ok , got it. Thanks

You mean that you tried to do that on the 2015 year model too ? - i mean to reset the ISC. Something i don't understand here , i changed all the throttle bodies as a set and the issue was solved , how do you explain that ?. I didn't reset the ISC..

According to the manual : To erase the ISC (idle speed control) learning data , set the start/engine stop switch from "start to stop" 3 times in 5 seconds , did you tried that too ?. I have the 2019 model , do you have the 2015 model year that you can enter the diag mode ?.

Ok , update what is your find.

Hi , yes i solved it !. I have to replace all the throttle bodies as a set from Ebay... Cost me 100 euro. I tried a lot of options BUT replacing it saved me. Learned my lesson..

Hi , the project is done. All is working as it should. My concern was on the front headlight , but it is the same on all the years 2015-2020. Thanks

The bike is Tracer 900 GT 2019 , i should update my picture...

Thanks .

Hi , i'm feeling that my front brake lever is a little spongy like there is air in the system. I tried to bleed the system and it's much better , i saw in youtube that if i put overnight pressure on the front brake lever the air bubbles that trapped inside will go up in the morning when i release the pressure and that will improve the braking action. So i have done that and in the morning i saw that the front lever is not holding presure and it went all inside , no leaks in the front brake tubes or connections. Do i need a rebuild kit to the front master cylinder ? or what ?. Thanks

If it's from GIVI it's been tested . So don't worry.

Is it good to do some service while it's up ? . I mean secure... Price spend ?.

I already have this pdf with the instructions. There are 4 wires at the plug. It should be lighted orange at start = off , first push low heat = green , second push high heat = red. Next push orange again = off. The colors of the wires are white , green , brown , red. If i push the switch what is the connection on the wires ?. Thanks

Hi , i found a heated seat that comes without the operating switch for my tracer GT 2019. Yamaha doesn't sell the switch , only the all package , a switch with a seat complete. Can anyone here share the switch picture / internals and how many wires does it have ?. Thanks

Hi , I have managed to buy a heated seat without the switch to operate it ... There are 4 wires at the plug. It should be lighted orange at start = off , first push low heat = green , second push high heat = red. Next push orange again = off. The colors of the wires are white , green , brown , red. If i push the switch what is the connection on the wires ?. Thanks

Hi , in this model when a check engine light turns on you can't reach the menu. You need a bar code scanner to delete this light. Search for a thread like this in the forum. Thanks